Using the CLR will eliminate any bleeding from the gun. Observing blueing is a controlled form of rust. Let it soak for 10-15 minutes.
I haven’t tried it on a gun barrel yet, but we use it a lot at work to remove rust. It will severely discolor / etch some alloys, so I will clean it later.
Naval Jelly or another rust neutralizer will instantly remove knuckles and some types of anodization.
Go to the hardware store and buy 0000 grade steel wool, then use & Jump # 9 to remove the rust. What you need to know, however, is that the wind has already passed under the grate. But in any case, the ultra-fine steel wool does not harm the remaining bruises, the rust has not yet been destroyed.
Use the steel wool pad as an abrasive to scrub the surface of the gun. Then put the gun cleaner on the steel wool and lightly rub the rusty area. After a while, clean the gun with or with towels and inspect it carefully. If rust persists, repeat the process until the firearm is free of rust.
- Enhance the performance of your firearms with Hoppe’s high-quality cleaners and lubricants. From highly viscous lubricating oils and water repellent lubricants for corrosion protection to Moly & Gun grease for heat and pressure protection. Hoppes is the world leader in gun cleaning and lubrication.
Hope n. 9 was never intended as a lubricant, it is primarily petroleum. It’s great as a drill cleaner, but should be cleaned and then replaced with a good gun oil.
Loctite Naval Jelly Rust Dissolver is the original rust treatment formula used for over 25 years. Removes rust from metal surfaces such as iron and steel. Loctite Naval Jelly Rust Remover can be applied by brush or spray on metal surfaces.
Sea jelly does this by converting the rust into a soluble iron compound that you can rinse off with water. It is effective because the main ingredient is phosphoric acid, which is one of the few acids capable of doing this. Other stronger acids will ■■■■■■ the metal and cause more rust.
WD40 to remove rust. Although WD40 is not only used to remove rust, it is considered a cleaner that can be used in that function as well. The reason it works is the WD40’s ability to cut and dissolve rust, restoring the bare metal surface.
Dry the gun immediately with a clean cloth. Do not use alcohol to dust or clean a gun magazine. It can replace or replace a historic finish. Also, do not use liquid or aerosol products as most leave mineral oils that trap dust.
For more stubborn rust, try white vinegar. The acetic acid in this common household product is acidic enough to dissolve the rust. You can dip smaller items like earrings, wipe them on a surface with an old rag, or just pour them directly onto rust stains or bolts and screws that have rusted together.
Never immerse the gun in anything without removing the excess, especially the WD40. On the external metal parts, the WD40 will do a good job. The WD40 performs well on the pitch. Do not spray any internal parts with WD40 unless you intend to take it all apart and clean it later.
- White vinegar / hydrogen peroxide cleaner. When lead and other metals build up it becomes a problem, a mixture of a 5050 mixture of white vinegar and hydrogen peroxide breaks down. I haven’t personally used this blend to clean guns, but it has a reputation for being a great DIY solvent.
Remove rust with vinegar Soak the rusted object in undiluted white vinegar. If the item is too large, spray or dab some vinegar on the rusty area. Let the vinegar sit for at least 30 minutes.
The defense industry makes and sells all of these anticorrosive products to hide the fact that they are a real threat. Guns rust and corrode in crates. In fact, corrosion occurs much faster in weapon cases, and the corrosion process is much faster.
To start, you’ll need some light oil (good ol '3in1 will do), a medium sized brass brush, some paper towels and a pre-1982 wreath. Pick a spot to start, pour some some oil on the metal, rub the crown in place and dry with a paper towel. Repeat until the rust is gone.