What is the p0014 code for a Chevrolet Colorado?
Chevy Colorado P0014: Camshaft Position B → Advanced Up → Bank 1. P0014 is a relatively common trouble code for vehicles with variable valve timing (VVT). This also includes the Chevrolet Colorado. The VVT adjusts the position of the camshaft at different engine speeds and loads to maximize the operating efficiency of the engine.
Here how to fix the p0014 code?
- Reset the error codes and take a test drive.
- Change the oil and filter to the correct oil viscosity for the engine.
- Repair or replace the camshaft oil check valve threads for bank 1 exhaust camshaft.
Can a low oil level cause p0014? Accumulation of sludge can cause DTC P0014 oil to flow to the engine. Sludge occurs when the engine runs on low oil, ignoring or passing an oil change, the PCV is malfunctioning, or poor quality oil is used. Change the oil, clear the code and drive the car.
Secondly, how much does it cost to fix the p0014 code?
Find out the price you will have to pay to have your car repaired. The average cost to replace a camshaft sensor is between $ 180 and $ 244. Labor costs are estimated to be between $ 75 and $ 96, while parts cost between $ 105 and $ 148.
What is the p0014 code for a Chevy Malibu?
P0014 is the OBDII generic code that will indicate to the engine control module (ECM) that the bank 1 exhaust camshaft is further advanced than what is indicated by the ECM. This may be for an advanced condition when advancing or decelerating the cam timing.
What is the error code p0014?
DTC P0014 will occur if the ECM detects that the bank 1 exhaust camshaft has advanced beyond what the ECM requires. This can occur when the camshaft timing is retarded or advanced, resulting in an overly advanced condition.
Can I drive the car with the wrong camshaft sensor?
If the engine appears to be running normally, you can probably get it running. However, if the engine fails (you will see a flashing engine light) it is NOT OK to keep everything running without the risk of injury. Diagnostic trouble codes can never be used to judge parts directly.
How much does it cost to repair the camshaft?
Pay between $ 120 and $ 300 to replace a camshaft sensor. Parts alone cost $ 50 to $ 200. Labor cost for a professional replacement is $ 70 to $ 100. Expect to pay more if you have a luxury vehicle or if the local dealer makes the exchange.
What are the symptoms of a bad camshaft sensor?
Symptoms of a bad or failing camshaft sensor Your vehicle does not drive as it did before. If the vehicle idles, stops frequently, has less engine power, drives frequently, consumes less fuel, or accelerates slowly, these are all signs of a camshaft sensor failure. Check that the engine light comes on. The vehicle does not start.
What causes a camshaft sensor to fail?
Improper Wiring: Loose wiring, oil, or debris can create improper voltage, grounding, or return issues that can lead to wiring problems. This loss of voltage or wear on the wires can cause the crankshaft sensor to fail.
Can you drive with a faulty VVT solenoid valve?
The VVT system normally only activates when the engine is accelerated or engaged for load situations such as driving uphill. However, if the VVT solenoid valve fails, it can add additional engine oil to the VVT transmissions.
Where is the camshaft sensor located?
The camshaft sensor (CMP) is mounted on the front of the cylinder head under the timing belt cover. The camshaft sensor (CMP) is located on the right side of the engine compartment behind the valve cover near the intake manifold.
How long does it take to replace a camshaft sensor?
How long does a camshaft last?
So if you pay attention to proper oil supply and maintenance, the camshaft will likely last as long as the engine, as recommended by the manufacturer. However, it should be noted that cars, at least in Europe, are designed for a service life of around 250,000 km.
What is a bank 1 camshaft actuator circuit?
Vehicles with variable valve timing (VVT) use a special solenoid valve called a camshaft actuator. This magnet is capable of regulating the oil pressure and thus controlling the control of the cam. The P0010 code is set when the ECU detects a low voltage in the VVT circuit that matches the input crest of bank 1.
How much does a crankshaft sensor cost?
The average cost of replacing the crankshaft position sensor is between $ 190 and $ 251. Labor costs are estimated to be between $ 102 and $ 130, while parts are between $ 88 and $ 121. Estimates do not they include taxes and fees.