The only tool needed to replace a thermocouple is a wrench. Use this to unscrew the connector securing the thermocouple to the gas valve, then disconnect the probe from the clamp and remove the thermocouple assembly. Close the gas supply valve beforehand.
Place the new thermocouple in the same place as your old device and close the fireplace to perform a test. Turn the throttle back on and turn on the lights. Let the thermocouple heat up for about 15 minutes, then light the flame to make sure everything is working.
The thermocouple in your gas fireplace is a heat sensitive device that keeps the igniter open while the igniter burns. This is done by generating a small electric current in the range of 10 to 30 millivolts as a signal to the throttle valve.
A standard replacement thermocouple costs our customers only 7 to 9, obviously the labor cost for one exit is 40.00 (still cheap).
If you don’t light the flame at all and you are sure the gas is on, there is likely a blockage in the ignition tube. If the flame goes on and off when you release the gas control knob after holding it for the recommended 20-30 seconds, there is an indication of a thermocouple fault.
The thermocouple relaxes and ignites the fire. The thermocouples have been thoroughly tested and should last for many years. In fact, experts believe a four-year audit cycle is enough to make sure things are working as they should.
Select Ohm or Resistance on the multimeter. Place one tip on the side of the thermocouple and the other on the end that screws into the gas valve. If the thermocouple has good continuity, you should see a small resistance reading on the multimeter.
Burner 1 unit The cause of the indicator lamp not lighting up is a worn thermocouple. It is easy to replace and costs from 5 to 10. Instead of trying to loosen the thermocouple in the combustion chamber of the boiler, it is easier to remove the burner and the thermocouple assembly.
Testing a Thermocouple for a Gas Fireplace Step 1 - Locate the gas valve and pilot flame. The thermocouple looks like a long copper wire running between the pilot and the gas supply valves. Step 2: Keep the pilot open to heat the thermocouple. Press the control valve and ignite the pilot flame. Step 3 - Visualize the pilot with the main burners on.
Universal thermocouples. Universal thermocouples, as the name suggests, work on most water heaters. They are available online and in hardware stores for a reasonable price. The length and type of thread are the two things to consider when buying.
Method 1 Turn on the control light Look for the control lights on the gas valve. Turn on the light for 30 seconds. Release the button to see if the light goes out. Shut off the gas supply to retest the thermocouple. Count to 20 and wait for the lights to go out.
The thermocouple looks like a piece of metal tube that is smaller than a straw. To find it, first find the gas control box. This is the box where the main gas line enters, which is where you ignite the gas in the oven. The other end of the thermocouple is in the pilot flame.
Thermocouple Replacement 20 150 Calling a professional plumber to install a new thermocouple should cost up to 150. If you do the job yourself, you only pay the price of the part, which is around 20.
Gas fireplaces must be inspected and cleaned every year. There will be no soot or creosote in the fireplace because you won’t be burning wood, but you can find bird nests that need to be removed.
Thermocouple / Thermopile Home Depot.
Remove the thermocouple from the pilot flame, wipe the nozzle lightly with steel wool or a cloth and remove any soot or deposits that may have formed due to a poor pilot flame. Use a rod pin to clean the threads of the nut connecting the thermocouple to the control valve, then retighten.
The thermocouple is part of a gas stove that is located near the pilot flame. There is a safety device that cuts off the gas if the light goes out or the electrical ignition is lost.