I think sandtex paint is the best color for your sleepers. To remove your sleepers the wire brush would do the job, but if the glossy black is two-ply it might be better to have a sharpener with a wire brush on top.
The easiest way to remove them is also the most messy, which is chemical stripping. You can make an inexpensive package using caustic soda, flour, and water. Flour is used only to form a dough. Apply generously on the edge and cover with a film so that it does not dry out.
- Place a dripping rag in front of the window and use a scraper to remove as much old paint as possible.
- Fill the holes with putty and let them dry completely.
- Gently sand the patched areas so they are flush with the rest of the sill, then sand the sill and sill to prepare for painting.
- Before cleaning, use a small whisk to remove dust and sand from the edge.
- Mix 1 tablespoon of mild liquid soap, eg. B. a Castilian soap, with 1 liter of warm water in a bucket.
- Scrub the window frame with soapy water and a mildly abrasive sponge or coarse cloth.
Gloss or semi-gloss acrylic or latex paints are perfect as they level for a smooth, professional-looking surface. When the paint has dried, apply another layer if necessary. Remove the masking tape and enjoy your new window sill!
Scrape loose colored tiles with a scraper, e.g. B. a palette knife or 5 in 1 painting tool, from the windowsill. Hold the scraper so that the blade is at a low angle, almost parallel to the window frame. Scrape with the grain of the tree as you scrape off the paint, being careful not to dig into the wood.
Painting tip No. 4 Painting Techniques That Help Avoid Brush Strokes
When the windows are clean and dry, you can start priming. All areas of bare wood should be primed with a water based wood primer such as Dulux Water Based Gloss Wood Primer. If your frames are metal, choose a special metal primer. When the primer is dry, you are ready to paint!
Use a putty knife or scraper to remove chipped and cracked paint. Sand the surface with a 100 mm scouring pad. Use a 220 gravel sponge to get a very smooth surface. Cover the areas where you don’t want paint splattered with a plastic washer.
Choose a masonry primer (like this one) so you know it will stick to the stone and let it dry completely before painting. Since you usually choose satin paint for the walls, flat for the ceilings and semi-gloss for the moldings and doors, but for the stone I say you can do whatever you want.
- Use a stiff brush to scrub the surface over any damaged areas.
- Sand some rough concrete parts with coarse sandpaper.
- Rinse the concrete window frame well to remove crumbled concrete and dust.
- Repair small to medium sized cracks in the concrete window frame with putty.
Like the primer, the masonry can be done with normal latex or oil paint, although there are masonry paints that increase the water repellency of the walls.
Use a high-pressure hose with hot water to wash the house lye off the wall. Your brick wall will reveal itself when you wash the dishes. With the peel option, you need to put the peel strips on top of the mixture. Let the strips sit for the specified time and peel them off to remove the paint.
The use of this marble painting method is not limited to window frames. If you have marble countertops or countertops, this works well too. Carefully remove a blank with 36 grit sandpaper. Make sure no shiny stains remain on the marble, the paint does not stick to it.
Before starting work, place a layer of fabric under the windowsill. 2 Remove chipped paint with a wire brush or coarse sandpaper. Remove the dust with a rag or brush. 3 If there is mold or moss, scrape and brush away as much as possible before treating with antifungal wax.
Scrape off the loose paint with a scraper until all flaky paint is removed. Wash the porch with soap and water to remove dirt and allow the area to dry completely. Lightly sand the paint surface with medium gravel if there is wax or grease residue on the paint.